Copyright © 2009 Floorz To Your Doorz LLC All rights reserved
Is it possible to install a solid wood floor on a concrete slab?
It is generally not recommended to install solid wood flooring over a concrete slab. Although this is the general rule,
there have been successful installations of solid wood flooring installed over dry, concrete slabs. This entails several
additional steps. A plastic barrier is set over the slab and taped at all seams. Then some sort of moisture-resistant
wood subfloor (marine plywood) is built on top of the plastic film. Then the flooring is nailed to the wood subfloor. If
you decide to take the chance be sure to consult with the manufacturer as to their recommendations. Be aware, you
may be voiding your warranty.
There is a new synthetic underlayment product on the market (called Sika AcouBond) that may allow for installing
solid wood flooring over a dry slab. Check with the manufacturer of the wood floor to see if they will warranty this type
of installation and what their recommended installation procedures are for this type of installation.
What types of wood flooring can I install on a concrete slab?
With the improvements in hardwood floors most engineered and longstrip engineered plank floors can be used over
a concrete slab. Manufacturers do not recommend using solid wood floors over a slab. Engineered planks and strip
wood floors can be glued directly to a clean, dry, well-cured concrete slab. Some engineered wood floors can be
glued at the tongue and grooves and then allowed to be floated over a special padding that is laid over the concrete
slab. Longstrip engineered planks can be floated over the slab with a padding underneath. There are some new
"hybrid" engineered floors that can be floated over a concrete slab and come with a click (glueless) tongue and
groove locking system.
Note: New concrete slabs need to be fully cured for a least 60 days. All wood planks should be acclimated for 24-48
hours prior to installation. Be sure to read and follow the manufacturer's recommended installation procedures.
Can we install a hardwood flooring over an existing vinyl floor?
Yes and no. Is the vinyl flooring is tightly secured to the subfloor? Does the vinyl flooring have a thick cushion
attached? If the vinyl floor is thin and well secured to the subfloor you may be able to float a wood floor over it. In
some situations you may be able nail/staple a wood floor over it also. If the wood subfloor is sound you may be able
to nail a solid wood floor over the top. Be sure to get the manufacturer's installation procedures for going over an
existing vinyl floor and be sure to check if this type installation is warranted by the manufacturer.
What to I do to remove scratches in my wood floor?
This really depends on the type of wood floor you have, the finish you have and how deep the scratches are in the
top layer. For small minor scratches in a urethane finish you should be able to order a touch-up kit from the store
you purchased the flooring from. Be sure to use the manufacturer's recommended finish products and test first by
applying a small amount in an out of the way area. For deep scratches you will probably have to have a professional
do a screen and recoat. This is where they use special sanding screens to lightly abrade the floor's finish to help the
new urethane bond better to the existing finish. With some wood floors you may be able to just replace the damaged
boards. It is best to leave the sand and recoat, or board replacement to a professional flooring installer, or refinisher.
Can I install a hardwood floors if I have pets?
Although many homeowners have pets, hardwood flooring is not designed for the abuse a dog or cat can cause on a
floor. Urine may permanently discolor the finish of the wood floor and large dogs' claws will probably leave scratches
in the finish. The type of wood floor you buy, the color and the finish will also be factor in how much punishment the
floor's finish can withstand before showing scratches and excessive wear.
Can an engineered wood floor system be refinished?
Some of the better quality engineered wood floors have a 1/8" thick finish layer and can be sanded and refinished 1
or maybe 2 times. The sanding and refinishing of an engineered wood floor is best done by an experienced
hardwood flooring refinisher. If you have heat vents in your floor you can remove a heat cover to get a side view of
your wood floor. This will help you check to see how thick you finish layer is. Always consult with the manufacturer to
see if the recommend sanding and refinishing of the engineered wood floors.
Can I use throw rugs on my hardwood floor?
Before using any throw rugs on your wood floor you should know the type of finish you have on the floor. All rugs
should be non-staining, meaning the colored dyes will not bleed. Generally in the presence of moisture, some dyes
used in rugs may bleed through onto your floor and discolor the wood floors surface. Also, be sure the rug does not
have a rough backing material that may scratch the surface of the floor. Clean dirt and debris from under the rug
regularly. To prevent possible shading of the wood underneath the rug, move the rug occasionally.
How do we stop wood flooring from gapping?
Gapping in solid wood floors cannot be stopped completely. Wood expands and contracts with changes in humidity.
Using a humidifier during the heating months may help reduce the amount of gapping in solid wood floors. Also,
some wood species may gap expand and contract less than others. Engineered wood floors are much more
dimensionally stable than solid wood floors and will show little or no gaps between planks.
What type of pads should I use under furniture legs?
Most flooring stores carry the recommended felt pads for using under chair legs and other furniture. The felt pads
come in various sizes. Some pads just stick on the bottom of the legs and others need to be nailed on. Never hit the
pads directly with a hammer. Follow the directions provided with the pads. Check and clean the pads often to prevent
debris, dirt and small particles from being trapped in the pad, which may cause scratches in the wood floor's finish.
It is generally not recommended to install solid wood flooring over a concrete slab. Although this is the general rule,
there have been successful installations of solid wood flooring installed over dry, concrete slabs. This entails several
additional steps. A plastic barrier is set over the slab and taped at all seams. Then some sort of moisture-resistant
wood subfloor (marine plywood) is built on top of the plastic film. Then the flooring is nailed to the wood subfloor. If
you decide to take the chance be sure to consult with the manufacturer as to their recommendations. Be aware, you
may be voiding your warranty.
There is a new synthetic underlayment product on the market (called Sika AcouBond) that may allow for installing
solid wood flooring over a dry slab. Check with the manufacturer of the wood floor to see if they will warranty this type
of installation and what their recommended installation procedures are for this type of installation.
What types of wood flooring can I install on a concrete slab?
With the improvements in hardwood floors most engineered and longstrip engineered plank floors can be used over
a concrete slab. Manufacturers do not recommend using solid wood floors over a slab. Engineered planks and strip
wood floors can be glued directly to a clean, dry, well-cured concrete slab. Some engineered wood floors can be
glued at the tongue and grooves and then allowed to be floated over a special padding that is laid over the concrete
slab. Longstrip engineered planks can be floated over the slab with a padding underneath. There are some new
"hybrid" engineered floors that can be floated over a concrete slab and come with a click (glueless) tongue and
groove locking system.
Note: New concrete slabs need to be fully cured for a least 60 days. All wood planks should be acclimated for 24-48
hours prior to installation. Be sure to read and follow the manufacturer's recommended installation procedures.
Can we install a hardwood flooring over an existing vinyl floor?
Yes and no. Is the vinyl flooring is tightly secured to the subfloor? Does the vinyl flooring have a thick cushion
attached? If the vinyl floor is thin and well secured to the subfloor you may be able to float a wood floor over it. In
some situations you may be able nail/staple a wood floor over it also. If the wood subfloor is sound you may be able
to nail a solid wood floor over the top. Be sure to get the manufacturer's installation procedures for going over an
existing vinyl floor and be sure to check if this type installation is warranted by the manufacturer.
What to I do to remove scratches in my wood floor?
This really depends on the type of wood floor you have, the finish you have and how deep the scratches are in the
top layer. For small minor scratches in a urethane finish you should be able to order a touch-up kit from the store
you purchased the flooring from. Be sure to use the manufacturer's recommended finish products and test first by
applying a small amount in an out of the way area. For deep scratches you will probably have to have a professional
do a screen and recoat. This is where they use special sanding screens to lightly abrade the floor's finish to help the
new urethane bond better to the existing finish. With some wood floors you may be able to just replace the damaged
boards. It is best to leave the sand and recoat, or board replacement to a professional flooring installer, or refinisher.
Can I install a hardwood floors if I have pets?
Although many homeowners have pets, hardwood flooring is not designed for the abuse a dog or cat can cause on a
floor. Urine may permanently discolor the finish of the wood floor and large dogs' claws will probably leave scratches
in the finish. The type of wood floor you buy, the color and the finish will also be factor in how much punishment the
floor's finish can withstand before showing scratches and excessive wear.
Can an engineered wood floor system be refinished?
Some of the better quality engineered wood floors have a 1/8" thick finish layer and can be sanded and refinished 1
or maybe 2 times. The sanding and refinishing of an engineered wood floor is best done by an experienced
hardwood flooring refinisher. If you have heat vents in your floor you can remove a heat cover to get a side view of
your wood floor. This will help you check to see how thick you finish layer is. Always consult with the manufacturer to
see if the recommend sanding and refinishing of the engineered wood floors.
Can I use throw rugs on my hardwood floor?
Before using any throw rugs on your wood floor you should know the type of finish you have on the floor. All rugs
should be non-staining, meaning the colored dyes will not bleed. Generally in the presence of moisture, some dyes
used in rugs may bleed through onto your floor and discolor the wood floors surface. Also, be sure the rug does not
have a rough backing material that may scratch the surface of the floor. Clean dirt and debris from under the rug
regularly. To prevent possible shading of the wood underneath the rug, move the rug occasionally.
How do we stop wood flooring from gapping?
Gapping in solid wood floors cannot be stopped completely. Wood expands and contracts with changes in humidity.
Using a humidifier during the heating months may help reduce the amount of gapping in solid wood floors. Also,
some wood species may gap expand and contract less than others. Engineered wood floors are much more
dimensionally stable than solid wood floors and will show little or no gaps between planks.
What type of pads should I use under furniture legs?
Most flooring stores carry the recommended felt pads for using under chair legs and other furniture. The felt pads
come in various sizes. Some pads just stick on the bottom of the legs and others need to be nailed on. Never hit the
pads directly with a hammer. Follow the directions provided with the pads. Check and clean the pads often to prevent
debris, dirt and small particles from being trapped in the pad, which may cause scratches in the wood floor's finish.